Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Rock Wall

Violation Summary

Violations Issued This Season: 8 Violations Complied at Time of Inspection: 4
Rock Wall Violations
Date Cited Description Violation
7/6/2017 Tighten the loose bolt for the top set of pulleys on the wire rope numbered 4479. COMPLIED AT VISIT45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
8/3/2017 Install missing bolt for the top pulley system that keeps the cables from coming off the top of it. Photo sent to Phil, Stacey was also shown.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/3/2017 Install missing bolt on the third joint of the fiberglass to the center of the metal frame. Shown to Stacey and photos sent to Phill.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/9/2017 Properly weld the crack at the top of wall on frame right in the middle. Complied at visir45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/6/2017 Repair the broken weld on the back side of the wall frame above the top pivot connection for the red hydraulic ram near the 1 1/2"" square metal stock. Marked with a white paint pen.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/6/2017 Fix /replace the three out of eighth hydraulic hoses that are leaking on the bottom of the hydraulics tanks for the safety cables, marked with orange tape.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/6/2017 Remove from services the safety climbing harness that is made by Vertical Reality it is marked with a white (X) on the back side of the tag. Its missing the manufactures tag info. COMPLIED AT VISIT45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/6/2017 Remove from services the defective carabiner made by Black Diamond 24 7 7kn ce 033314. Marked with a white (X) and also no good. COMPLIED AT VISIT45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.

View All Events Listing

Thanks for the feedback! It will help us improve your experience.