Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Kiddie Ferris Wheel

Violation Summary

Violations Issued This Season: 9 Violations Complied at Time of Inspection: 3
Kiddie Ferris Wheel Violations
Date Cited Description Violation
6/3/2017 Properly remove the bird droppings on the seats of the kiddie wheel. Complied at visit.45-1.17
45-1.17A suitable number of containers for refuse shall be provided in and around amusement devices, temporary structures, viewing stands and tents. Excessive accumulations of trash or refuse shall be promptly removed. All parts of amusement devices, temporary structures, viewing stands and tents used by passengers or customers shall be maintained in a clean condition.
7/23/2017 Do not load tub 6 until the accumulation of filth is removed and tub is cleaned.45-1.17
45-1.17A suitable number of containers for refuse shall be provided in and around amusement devices, temporary structures, viewing stands and tents. Excessive accumulations of trash or refuse shall be promptly removed. All parts of amusement devices, temporary structures, viewing stands and tents used by passengers or customers shall be maintained in a clean condition.
7/23/2017 Tighten sweep arm nut45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/23/2017 Repair metal cage at the bottom of the far side of tub 1 - some welding required.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/23/2017 Repair metal cage of tub 5 where broken on left hand side of the far side from entry point, as pointed out to owner.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/23/2017 Repair metal cage of tub 6 where broken on left hand side of the far side of the entry point, as pointed out to the owner.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/23/2017 Repair metal cage of tub 3 where broken on far side near the bottom as pointed out to the owner.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/23/2017 Adjust set of stairs to comply with step height requirements.45-2.13(c)
45-2.13(c)Stairways and ramps shall be at least 18 inches wide. Stair treads shall be at least nine inches deep exclusive of nosing and the height of rise shall not exceed eight inches. Between any two levels the treads shall be of uniform depth and the risers of uniform height. The slope of ramps shall not exceed one in four. The open sides of stairways, ramps and platforms shall be provided with adequate protection against falling, except as the safe and normal access to the device may otherwise require.
7/7/2017 Supply a acquit set of stairs to the ride. Two 6x6 pieces of wood is not acceptable. DO NOT OPERATE THE WITH OUT A ACQUIT SET OF STAIRS.45-2.13(c)
45-2.13(c)Stairways and ramps shall be at least 18 inches wide. Stair treads shall be at least nine inches deep exclusive of nosing and the height of rise shall not exceed eight inches. Between any two levels the treads shall be of uniform depth and the risers of uniform height. The slope of ramps shall not exceed one in four. The open sides of stairways, ramps and platforms shall be provided with adequate protection against falling, except as the safe and normal access to the device may otherwise require.

View All Events Listing

Thanks for the feedback! It will help us improve your experience.