Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Wipe Out

Violation Summary

Violations Issued This Season: 44 Violations Complied at Time of Inspection: 14
Wipe Out Violations
Date Cited Description Violation
7/7/2017 Do not load tub 14 until repaired leg guard is re-installed.45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/3/2017 Repair or replace seatbelt on tub 1.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/11/2017 Ensure the lap bar to tub 10 stays up during loading and unloading.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/11/2017 Enusre the lap bar to tub 11 stays up during loading and unloading.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/11/2017 Repair or replace the seatbelt to tub 20.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/11/2017 Ensure the exit gates close.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/11/2017 Replace sprung r-key under tub 5.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/27/2017 Repair the seat belt in car #8, inside seat. COMPLIED AT VISIT45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/27/2017 Repair the outside seat belt in Car #19. It will not release to hook. COMPLIED AT VISIT45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/27/2017 Secure the loose piece of metal trim car #2 near the led light. COMPLIED AT VISIT45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
9/15/2017 Repair or replace seat belt on inside seat of tub #3. DO NOT LOAD until complied45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Ensure all exit gates automatically close.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Fully secure tub 18 to frame. Do not load until fully secured.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Unjam seatbelt in tub 18. Do not load until repaired.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Repair floor, front left quadrant, as flagged.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Cover screw thread sticking out next to interior seat of tub 3 - do not load until covered.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Replace ripped sticker ""Caution larger person sit in outside seat"" on tub 3.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Secure trim piece on tub 12 as flagged.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/7/2017 Repair leg guard on tub 14.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Reinstall portruding rivit on tub 14 - do not load until complied.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Repair or replace male end seatbelt on inside of tub 20. Do not load until complied45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Rivit down leg restraint on tub 20. Do not load until complied.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Remove burr on rivit on leg restraint on tub 1145-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Replace sprung r-key as flagged.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/7/2017 Replace broken air shock on restraint bar on seat #12. Complied at visit45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/1/2017 Replace Caution sticker inside seat # 6 that is missing or unreadable.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Replace Caution sticker inside seat # 4 that is missing or unreadable.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Replace Caution sticker inside seat # 1 that is missing or unreadable.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Replace Caution sticker inside seat # 12 that is missing or unreadable.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Replace Caution sticker inside seat # 18 that is missing or unreadable.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Replace Caution sticker inside seat # 20 that is missing or unreadable.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Repair/adjust the inside seatbelt on tub #9 so it retracts when pulled out. DO NOT LOAD THIS SEAT UNTIL COMPLIED45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Properly secure the loose floormat on tub #1. Complied at visit45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Install missing lock pin in restraint bar in car # 17. Complied at visit45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Repair non locking restraint bar (does not lock in open position for seat #245-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Repair non locking restraint bar (does not lock in open position) for seat #545-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Repair non locking restraint bar (does not lock in open position) for seat #745-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Repair non locking restraint bar (does not lock in open position) for seat #1145-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Repair non locking restraint bar (does not lock in open position) for seat #1245-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Repair non locking restraint bar (does not lock in open position) for seat #1345-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/7/2017 Replace worn/broken restraint bar padding on seat #145-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/1/2017 Install missing electrical cover on the inside of sweep arm to tub #1.45-2.21(a)
45-2.21(a)General requirement. All electrical wiring, equipment and apparatus used for amusement devices or for lighting shall be installed, operated and maintained in compliance with this Part (rule), Industrial Code Rule 57 High Voltage Proximity, and the National Fire Protection, National Electrical Code, NFPA 70-1999 (NEC-1999).
6/1/2017 Properly secure the loose LED light under sweep arm to tub #1. Complied at visit45-2.21(a)
45-2.21(a)General requirement. All electrical wiring, equipment and apparatus used for amusement devices or for lighting shall be installed, operated and maintained in compliance with this Part (rule), Industrial Code Rule 57 High Voltage Proximity, and the National Fire Protection, National Electrical Code, NFPA 70-1999 (NEC-1999).
8/11/2017 Ensure jacket for small guage electrical lines near boom is put back into and secured to electrical box.45-2.21(a)
45-2.21(a)General requirement. All electrical wiring, equipment and apparatus used for amusement devices or for lighting shall be installed, operated and maintained in compliance with this Part (rule), Industrial Code Rule 57 High Voltage Proximity, and the National Fire Protection, National Electrical Code, NFPA 70-1999 (NEC-1999).

View All Events Listing

Thanks for the feedback! It will help us improve your experience.