Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Round Up

Violation Summary

Violations Issued This Season: 13 Violations Complied at Time of Inspection: 5
Round Up Violations
Date Cited Description Violation
6/9/2017 The jam nuts on the cross bars were loose and not tight to the turn buckles.45-1.6(a)
45-1.6(a)Competent supervision. The assembly and disassembly of an amusement device, temporary structure, viewing stand or tent shall be done by or under the immediate supervision of a person experienced and instructed in the proper performance of such work in respect to the device, structure, viewing stand or tent.
5/25/2017 Replace the missing R key in the out rigger support connection pin on the back of the trailer. COMPLIED AT VISIT45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
5/25/2017 Tighten the bolt in the locking plate that holds the pin in for the hydraulic ram. COMPLIED AT VISIT45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/11/2017 Install missing r-key in tension cable attachment point above tub #27. Complied at visit45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/25/2017 Repair the broken safety mesh in seat #16. It starts on the right side of back pad and goes behind the back pad. DO NOT LOAD UNTIL COMPLIED45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Properly repair/replace the piece of support tubing behind and between tubs # 22 & 23.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Repair broken caging at foot level inside tub #2545-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
8/11/2017 Repair broken caging at foot level inside of tub #2945-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
9/22/2017 Four main support sweeps have rusted through. Consult an engineer or manufacturer for a repair procedure. Make all repairs before putting this device in service. ***Do Not Load Passengers***45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
9/22/2017 Four main support sweeps have rusted through. Make all repairs meeting the design and construction requirements per 45-2.10(b) before loading passengers. ***DO NOT LOAD PASSENGERS UNTIL COMPLIED***45-2.10(b)
45-2.10(b)All amusement devices shall be designed, constructed and installed so as to withstand any normal stresses to which they may be subjected.
5/18/2017 Replace the defective restraint chain lock for tub # 14. DO NOT LOAD THIS SEAT UNTIL COMPLIED.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
5/18/2017 Properly Secure tub padding inside tubs # 1,15,21,28,30. Complied at visit45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
5/18/2017 Replace ripped padding inside tubs # 18 & 19.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
5/18/2017 Number all of the tubs so they can be easily read.45-2.5(b)
45-2.5(b)Each passenger carrying car, seat etc. in an amusement device or temporary structure shall be identified with an identification number in a readily visible location.

View All Events Listing

Thanks for the feedback! It will help us improve your experience.