Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Sooper Jet

Violation Summary

Violations Issued This Season: 6 Violations Complied at Time of Inspection: 1
Sooper Jet Violations
Date Cited Description Violation
7/18/2017 Tighten the seat belt connection on the male side in car #3. COMPLIED AT VISIT45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/12/2017 Repair/weld the crack through the aluminum tire tread that is sticking up on track section #4. Complied at visit45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/12/2017 Repair/weld the crack through the aluminum tire tread that is sticking up on track section #8. Complied at visit45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/12/2017 Repair loose broken plastic piece on the last drive car that has tape on it, currently dangling. Complied at visit45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
7/12/2017 Repair seatbelt in tub #1 so it does not detach with 2-3 lbs of pressure. DO NOT LOAD THIS SEAT UNTIL COMPLIED Complied at visit45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
7/12/2017 Provide a new seal on drive motor electrical junction box located in the last tub on the side of the drive motor.45-2.21(a)
45-2.21(a)General requirement. All electrical wiring, equipment and apparatus used for amusement devices or for lighting shall be installed, operated and maintained in compliance with this Part (rule), Industrial Code Rule 57 High Voltage Proximity, and the National Fire Protection, National Electrical Code, NFPA 70-1999 (NEC-1999).

View All Events Listing

Thanks for the feedback! It will help us improve your experience.