Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Sooper Jet

Violation Summary

Violations Issued This Season: 11 Violations Complied at Time of Inspection: 6
Sooper Jet Violations
Date Cited Description Violation
7/25/2017 Properly insert r-keys in the track wedges in track section #2 (2). Complied at visit45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/25/2017 Properly insert r-keys in track wedges in section #6. Complied at visit45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
7/25/2017 Properly insert r-keys in (2) track support arm sections. Complied at visit45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
6/22/2017 Weld crack in track section #4 as indicated with white paint marker.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/2/2017 Tab number four (#4) has a crack45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
9/15/2017 Repair crack in track at the inside section of #2, from the tube through the crossmember. Do not operate until complied45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/29/2017 Install the 5- missing R-Keys on the track side of this ride.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/29/2017 Tighten the loose trolley wheels under this ride.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/22/2017 repair the seatbelt in tub #4 so it stays connected when pulled with approx 3-4lbs of force. Complied at visit45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
7/25/2017 Properly tighten the bolt on the inside edge of the seat #1 indicated with orange tape.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/22/2017 Provide a proper ID plate with manufaturer rated R.P.M.'s and other information described therein.45-2.5(a)
45-2.5(a)Every amusement device shall be identified by a trade or descriptive name and an identification number. A metal plate upon which there is legibly impressed the name and number of the device, its model number if any and the name and address of its manufacturer shall be firmly attached to the device in a readily visible location. The maximum safe number of passengers and the maximum safe speed, where applicable, shall be legibly impressed on the same plate or another metal place.

View All Events Listing

Thanks for the feedback! It will help us improve your experience.