Skip to Content Skip to Navigation

Amusement Device Detials

The New York State Department of Labor inspects all amusement devices on or before the scheduled start date of an event. Only those devices deemed safe are allowed to operate. Detailed inspection results for each individual device will be posted within two weeks of the event start date.

For more information, look at our Frequently Asked Questions.

Details for device: Tubs of fun

Violation Summary

Violations Issued This Season: 21 Violations Complied at Time of Inspection: 1
Tubs of fun Violations
Date Cited Description Violation
5/19/2017 This ride has violations that have not been repaired. Repair the violations or the permit shall be voided.45-1.12(d)
45-1.12(d)Any violation of this part may result in a revocation, provided that written notice of non-compliance is served upon the owner specifying any violation of this part and directing the owner to correct such violations within 30 days of receipt of such notice.
6/30/2017 Outstanding violations from July 2016 exist. Numerous violations exist from this inspection. Do not operate.45-1.13
45-1.13No person shall knowingly use, or suffer or permit to be used, an amusement device, temporary structure, viewing stand or tent, which is not properly assembled or which is defective or unsafe in any of its parts, components, controls or safety equipment.
6/9/2017 Repair the male end of the seat belt in tub #4 to the left of the door. COMPLIED AT VISIT45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
6/30/2017 Insert r-key to post securing rod to sweep arm between tubs 2 and 1.45-1.6(b)
45-1.6(b)Assembly work shall be performed in a proper and workmanlike manner. Parts shall be properly aligned, and shall not be bent, distorted, cut or otherwise injured to force a fit. Parts requiring lubrication shall be lubricated in course of assembly. Fastening and locking devices, such as bolts, cap screws, cotter pins, lock washers, etc. shall be installed where required. Nuts shall be drawn tight, cotter pins shall be spread and lock nuts firmly set.
6/30/2017 Provide appropriate door locking hardware for tub 3.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Repair broken stitch weld for underside support bracket 2nd to the right from the entry door of tub 3.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Repair the seatbelt immediately to the left of the door on tub 3.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Tighten all seat nuts to bolts and secure them with double nuts or locking nuts on all tubs.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Provide for all missing seat bolts on all tubs.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Repair seat where seatbolt no longer secures seat, across from door, on tub 4 as flagged.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Repair or replace seat belt immediately to the left of entry door on tub 5, as it does not hold taught.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Secure tub 5 from excessive rocking in the up and down direction.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Secure piano hinge post in tub 6.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Secure tub 1 from excessive rocking in the up and down direction.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Repair or replace male end seat belt on tub 1, immediately to the right of the door, as it fails to remain taught.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Remove sharp corner on upper hinge side of door.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Replace female end of seatbelt on tub 2, as it is ripped more than halfway through - on seat immediately to left of door.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Secure male end seatbelt to seat on tub 2, immediately to left of door.45-1.6(c)
45-1.6(c)Parts which are excessively worn or which have been materially damaged shall not be used. Close visual inspection of parts shall be made during assembly to discover such wear or damage and immediate inspection of fastening devices shall be made after assembly to assure that they have been properly installed.
6/30/2017 Straighten front corner jack post.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/30/2017 Completely rebuid tub 3 so as to provide for secure and safe seating, eliminate gaps between seat and outer shell, and allow for all seat bolts to hold the seat as manufactured.45-2.20
45-2.20The interior and exterior parts of all passenger-carrying amusement devices with which a passenger may come in contact shall be smooth and rounded, free from sharp, rough or splintered edges and corners, with no protruding studs, bolts, screws or other projections which might cause injury. Interior parts upon or against which a passenger may be forcibly thrown by the action of the amusement device shall be adequately padded. Devices which are self-powered and which are operated by a passenger shall have the driving mechanism so guarded and the guards so locked in place as to prevent passengers from gaining access to the mechanism. Such belts, bars, foot rests and other equipment as may be necessary for safe entrance and exit and for support while the device is in operation shall be provided. Such equipment and fastenings thereof shall be of sufficient strength to retain the passengers. The fastenings shall be of a type which cannot be inadvertently released
6/30/2017 Provide records of daily inspections and testing.45-2.7
45-2.7An amusement device shall be inspected and tested on each day when it is intended to be used. The inspection and test shall be made by a person experienced and instructed in the proper operation of the device and shall be performed before the device is put into normal operation. The inspection and test shall include the operation of control devices, speed-limiting devices, brakes and other equipment provided for safety. A record of each inspection and test shall be made at once upon completion of the test on a form provided by the commissioner or on a form approved by the commissioner with the information required by the section and shall be kept with the device and available to the commissioner for at least 30 days.

View All Events Listing

Thanks for the feedback! It will help us improve your experience.